Printed circuit boards, otherwise known as PCB are found in almost all electronic devices. In manufacturing of PCB, electricians who are amateurs can make their own boards by drawing a design and then giving it to the manufacturer. There are three types; single sided, multi layered and double side boards. They are usually conducted with nickel, copper or aluminum material, and the type used is determined by the complexity and density of the circuits. The process of making them is described below.
A conductive material is used to plate the backing. Conduction between the layers is enhanced by drilling holes into the backing. To remove any small conductor particles that may be present, the board is scrubbed. Filtration process is applied to recycle the recovered particles. This is because, if not recycled, the copper may form a mixture with the other wastes and then become quite hazardous to the environment.
The board is then cleaned. Etching also takes place to allow for proper adhesion in the next stage. Once this has been carried out, there is an addition of another layer of conductor. The process of electrolysis copper plating is applied in order to conduct the holes that had been drilled previously. Both alkaline based and acidic based solutions such as copper sulfate can be used to enhance pH balance.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Obtaining alternative resist can be achieved by use of other compounds that are photosensitive or organic. They can be used in their dry or wet forms. When exposed to ultraviolet light, they become hard.
The resists that are in liquid form can be applied using a roller, squeegee, spray or silk screen. This liquid can also be applied to the surface on one or both sides of the surface. Finer circuits can be achieved by using light.
The last stage in this process is forming multi layer panels. The layer's inner cores are assembled together. The resulting product is like a book which has a copper foil with sheets of epoxy that are alternating.
The book is positioned into a laminating press and then high pressure as well as heat is applied to it. The intense heat will eventually cause the sheets to melt down and a bond will be formed. Next, there are holes that are drilled into it. Prior to this, it should undergo some trimming and buffing. Manufacturing of PCB can only be successful if all these steps and guidelines are clearly followed to the latter.
A conductive material is used to plate the backing. Conduction between the layers is enhanced by drilling holes into the backing. To remove any small conductor particles that may be present, the board is scrubbed. Filtration process is applied to recycle the recovered particles. This is because, if not recycled, the copper may form a mixture with the other wastes and then become quite hazardous to the environment.
The board is then cleaned. Etching also takes place to allow for proper adhesion in the next stage. Once this has been carried out, there is an addition of another layer of conductor. The process of electrolysis copper plating is applied in order to conduct the holes that had been drilled previously. Both alkaline based and acidic based solutions such as copper sulfate can be used to enhance pH balance.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Obtaining alternative resist can be achieved by use of other compounds that are photosensitive or organic. They can be used in their dry or wet forms. When exposed to ultraviolet light, they become hard.
The resists that are in liquid form can be applied using a roller, squeegee, spray or silk screen. This liquid can also be applied to the surface on one or both sides of the surface. Finer circuits can be achieved by using light.
The last stage in this process is forming multi layer panels. The layer's inner cores are assembled together. The resulting product is like a book which has a copper foil with sheets of epoxy that are alternating.
The book is positioned into a laminating press and then high pressure as well as heat is applied to it. The intense heat will eventually cause the sheets to melt down and a bond will be formed. Next, there are holes that are drilled into it. Prior to this, it should undergo some trimming and buffing. Manufacturing of PCB can only be successful if all these steps and guidelines are clearly followed to the latter.
About the Author:
You can visit the website www.becman.com for more helpful information about What Goes Into Manufacturing Of PCB
0 comments:
Post a Comment